Construction Update #25 - A Tale of Two Projects

Old Placerville

Placerville Structures - McCarville Studios Placerville Cafe-Bar

April 20, 2024

Ny version of  Old Placerville will include several structures.  The first two, the fuel oil depot and stock pens have already been built; the first from a Ragg's...To Riches kit the second from two Banta Modelworks kits.  Three more are beng built from McCarville Studios kits; the cafe-bar, gas station and barn.

The McCarville Studios Placerville Bar-Cafe

I decided to start to with the cafe-bar.  I built the model per the instructions with the exception of the laser cut paper shingles included in the kit.  Based upon a close examination of the color photo on page 258/259, "The RGS Story, Vol 1" (Sundance Publishing), I came to the conclusion that the included shingles were to large and uniform when compared to those on the prototype.  I will probably end up using "peel & stick" shingles from Builders In Scale or Rail Scale Models.  In addition, due to the shallow pitch of the porch and rear shed, I decided that rolled roofing would probably be more appropriate than shingles.

Here is a picture of my model waiting for a roof.

Make no mistake that the McCarville Studios kit builds in to a very nice and interesting structure but I do have a couple of observations/suggestions.  First I think the instructions could be improved by adding more "how to" along with a couple of pages with larger photographs. I also question the use of MDF for the core material.  MDF is brittle, the corners are fragile and it is easily damaged by moisture.  Although there is no mention of it in the instructions, it should be sealed, especially the base, to protect the parts from moisture.  I exposed a piece of the MDF to water and watched it swell, warp and loose all of its rigidity.  As a result, I sealed all of the MDF with two generous coats of flat lacquer before I started any assembly.  I think 1/16" or 3/32" of marine plywood would be a better choice of material.  

I find that building up the sides to include the siding, windows, doors and trim, were possible, before attaching them to a base makes for easier assembly.  And, while there is some mention of interior bracing to prevent warping I think most kit or scratch built structures should include interior bracing regardless of the construction materials.  As can be seen in the following photo, I used 3/16" square strip wood  to add the bracing.  I used Aleen's "Original" Tacky Glue for all of the assembly.

Basic Scenery for Old Placerville

April 27, 2024

I am using a hillside to transition between the scenery around Old Placerville/Placerville and Ridgway.  I used a Woodland Scenics incline set to create the roadway followed by a series of "pink foam" profiles.  Eventually the caf-bar and gas station will be located in the foreground between the road and the tracks.

Here is a overall view of Old Placerville.  A staging track representing Montrose will be located behind the hillside and between the backdrop that has not yet been installed.  The Texeco fuel oil dealer was built from a "Ragg's... To Riches" kit by Bruce Hanley.   I built the stock pens using parts from two "Banta Modelworks" kits. The cafe-bar, gas station and bar will be located on the far left.

The profiles were covered by cardboard webbing, a layer of painters paper and then plaster cloth.  Generic plaster cloth can be purchased on Amazon for about half the cost of  similar products available from hobby shops.

The plaster cloth was then followed up with a layer of Sculptamold.

Basic Ground Cover

The "hard shell" was given mix of white glue and earth colored exterior house paint.  Paving sand was sprinkled on to the paint-glue mix along with several colors of fine turf.  Once the new backdrop is installed I will add more texture (trees, shrubs, grass, etc) in order to blend the Placerville-Old Placerville-Ridgway scenes together.  No, that corrugated shed doesn't belong in the stock pen!

As always, your comments, suggestions & questions are welcome

sdepolo@outlook.com

 

Construction Update #24 - Scenery around Placerville & Bridge 45A

Placerville

Scenes from around Placerville 

There are three grade crossing in Placerville.  The first one, south of the depot is shown below.  The crossings are from Tichy, the plank for the crossing were made from scale lumber and the caboose is a P-B-L model.

I built the depot from a Ragg;s kit.  It was painted with Floquil paints and weathered with Bragdon powdered pigments.  This figures are from Fun and Games.  I don't glue the figures in place.  Instead, I pin the figures in place so they can be easily moved or replaced.

There are a number of structures along Front Street behind the depot.  All of these are fronts about 2" deep.  The Placerville Garage was built with parts left over from the Monster Model Works Placerville Store.  Most of the trees here were built from Scenic Express Super Trees.

North of the garage is this little house.  It was scratch built using a photo off the internet.

The post office was right next door.  Again, it was scratch built using photos off the internet.  The flag pole is from Woodland Scenics and the figure from Fun and Games.

The PLacerville store was built from a Monster Model Works kit.  Again is is only about 2' deep.

 Another scratch built house built from photos located north of the store.

The second crossing north of the depot.  The #346 has uncoupled from it's train and pulled forward to clear the grade crossing.

This little material yard is located on the north end of the house track.

None of these little scenes are finished.  I need to add more details, additional ground cover, shrubs and static grass.

 

Bride 45A

April 14, 2023

 

Yes, work continues on Bridge 45A.  All 22 bents are now finished as is the bridge deck.  The prototype had 29 bents.  About 600 individual pieces of strip wood were cut, stained and assembled to make the bents.

North Bents

Center Bents

South Bents 

I cut 325 bridge ties for the bridge deck.  I ordered the wood from Northeastern Scale Models.  The wood from Mt. Albert or Kappler is nicer but the material from Northeastern is much cheaper, when purchased in bulk, and is "good enough" for bridge stock.

 As always, your comments, questions and suggestions are welcome

sdepolo@outlook.com 

Construction Update #23 - Scenery

Wilson - "Milepost 32.6.  Elevation 7.723 feet - was primarily a passing siding of 27 car capacity."  (Page #305, RGS Story, Volume 1, Sundance Publishing)

April 8, 2023

 

While Wilson is still lacking some detail to include additional ground cover, static grass,  shrubs, figures and water, it now provides an acceptable background for a few photos.  Here RGS #455, a K-27, has stopped for water.  Most if not all of the RGS water tanks were painted oxide red.  But since I have yet to find a actual picture of "Wilson" who is to say that the tank, if one ever existed, escaped the RGS B&B gang and a coat of oxide red paint.  The K-27 is from P-B-L and the water tank was built from a V&T Models kit.

 

Northbound leaving Wilson for Placerville.  The east bank of the San Miguel River is in the foreground.
 

 

The stock car was built from a P-B-L kit and the drop bottom gondola is from a V&T kit.  I don't think I have ever seen a picture of a drop bottom gondola on the RGS but there are a couple running around my version of the railroad.

The box car storage shed attached to the section house.  This kit-bashed model is based upon a similar structure that stood at Pagosa Junction.

 

Leased D&RGW #346 southbound at Wilson.  #346 is a P-B-L brass import equipped with DCC and Tsunami2 sound.  This model has an interesting background as it was originally lettered for Brian Ellerby's Copper River Yukon, then my Alaska Pacific and now the D&RGW.

Initial Scenery around Placerville

I typically start with earth colored paint followed by a layer of basic ground cover (paving sand) around a key scenic element; in this case the depot.

Here, the same thing has been done with the hotel, coal bin and small warehouse to the south of the depot.  The Bar Mills "Idaho Hotel" is a stand in for the original hotel.  A Banta warehouse kit, built by my 11 year old grandson, is another stand in for the Gallaway Stage Stop Building (He still needs to paint the roof). 

And in this case, the "scenic element" is a drainage ditch that was west of the depot.  A partial view of this ditch shows up a picture on page 273, Volume 1, RGS Story, Sundance Publishing.

As always, your comments, questions & suggestions are welcome

sdepolo@outlook.com